View L6238_307304.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

L6238
SENSORLESS SPINDLE MOTOR CONTROLLER
PRODUCT PREVIEW
2.5A, THREE-PHASE OUTPUT DRIVE PRECISION DIGITAL PLL FULLY-INTEGRATED ALIGN + GO START-UP ALGORITHM DIGITAL BEMF PROCESSING MASTER/SLAVE SYNCHRONIZATION BIDIRECTIONAL SERIAL PORT STAND ALONE OR EXT. DRIVER SHOOT-THROUGH PROTECTION DESCRIPTION The L6238 is a complete Three-Phase, D.C. Brushless Spindle Motor Driver system. The device features both the Power and Control Sections and will operate Stand Alone, or can be used in Higher Power Applications with the addition of an external Linear Driver. Start-Up can be achieved with the Fully-Integrated Align + GO Algorithm or may be sequenced manually for User-Defined start-up algoBLOCK DIAGRAM
PLCC44 ORDERING NUMBER: L6238
rithms. A Digital PLL provides high accuracy and the capability to do Master/Slave Synchronization for Disk Array configurations. Programmable functions include commutation Timing Adjustment and Slew Rate Control for peak efficiency and minimum noise. Protective features include Stuck Rotor\Backward Rotation Detection and Automatic Thermal Shutdown.
June 1993
1/35
This is advanced information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
L6238
ABSOLUTE MAXIMUM RATINGS
Symbol BVdss VPower VLogic VAnalog Vin Imdc Impk Ptot Ts Output Brakdown Voltage Motor Supply Voltage Logic Supply Voltage Analog Supply Voltage Input Voltage Peak Motor Current (DC) Peak Motor Current (Pulsed: Ton = 5ms, d.c. = 10%) Power Dissipation at Tamb = 50C Storage and Junction Temperature Parameter Value 17 15 7 15 -0.3 to 7 3 5 2.5 -40 to 150 Unit V V V V V A A W C
PIN CONNECTION (Top view)
THERMAL DATA
Symbol R th (j-pin) Rth (j-amb) Rth (j-amb) Parameter Thermal Resistance Junction-Pin Thermal Resistance Junction-Ambient (Float.) Thermal Resistance Value 7 68 34 Unit C/W C/W C/W
2/35
L6238
GENERAL DESCRIPTION The L6238 is an integrated circuit that will be used to commutate and speed control a 3-Phase, 8-pole, brushless, DC motor. The primary application is for disk drive spindle motors. This I.C. has the following features: No Motor Hall Effect Sensors are required for commutation or speed control. Timing information is determined from the Bemf voltage of the undriven motor terminal. On-board Speed Control via a Phase Locked Loop that accepts a once-per-rev reference frequency and locks the motor to that frequency. The L6238 can accomodate a wide range of speeds. The L6238 achieves Spindle Synchronization by locking to a once-per-rev reference that is common to multiple drives. The L6238 has a multiplexer that enhances the versatility of the controller. This first multiplexer selects either internal feedback, (generated by the Bemf of the motor), or external feedback (embedded index). An External P-Channel FET can be connected to the FET can be connected to the FET Bridge for Higher Power Applications. PIN FUNCTIONS
N. 1 2 3 4 5 6, 7, 17, 29, 39, 40 8 9 10 11, 42 12 13 14 15 16 18 19 20 21 22 Name OUTPUT B SPIN SENSE BRAKE DELAY R sense CHARGE PUMP 2 GROUND I/O I/O O I O I I Function DMOS Half Bridge Output and Input B for Bemf sensing. Toggless at each Zero Crossing of the Bemf. Energy Recovery time constant, defined by external R-C to ground. Outputs A+B connections for the Motor Current Sense Resistor to ground Negative Terminal of Pump Capacitor. Ground terminals.
In this configuration, the internal DMOS drivers are sequenced in full conduction state and the external PFET is the linear control element. An internal inverting buffer from the output of the OTA controls the conduction of the EXT PFET. An internal Virtual Center Tap is used if the motor center tap is not connected. The motor Current Limit can be set by an external resistor divider. A Serial Port is included so that I/O can be done with a minimum of pins. Key control and status lines are also bonded out to achieve a Minimum Configuration without using the Serial Port. Programmable Functions include Phase Switch Timing Optimization for motor efficiency, Speed Lock Threshold, Auto-Start or mP Supervised Spinup, and output current limiting gain. Energy Recovery Mode for Head Retraction, followed by Dynamic Braking Mode. Logic signals are CMOS Compatible. Stuck Rotor and Backward Rotation detection. Automatic Thermal Shutdown with early warning bit available in the status register
CHARGE PUMP 1 CHARGE PUMP 3 OUTPUT A Vpower Vanalog SER PORT DISABLE SER DATA R/W SER STROBE SER PORT CLK SER DATA I/O EXT/INT FREF ENABLE LINEAR OUTPUT ENABLE
I I I/O I I I I I I I/O I I I I
Positive terminal of Pump Capacitor. Positive terminal of Storage Capacitor. DMOS Half Bridge Output and Input A for Bemf sensing. Supplies the voltage for the Power Section. 12V supply. Input for tri-stating the serial port. Selects Serial Data Read or Write Function. Dtat Strobe Input. Clock for Serial Data Control. Data stream Input/Output for Control/Status Registers. Selects thr Internal BEMF Zero Crossing or an External Source as Feedback Frequency for te PLL. A zero on this pin passes the PLL Fref signal to the Freq/phase detector. This input should be grounded or left unconnected. Tristates Power Output Stage when a logic zero. 3/35
L6238
PIN FUNCTIONS (continued)
N. 23 24 25 26 27 28 30 31 32 33 34 35 36 37 38 41 43 Name RUN/BRAKE SEQ INCREMENT SYSTEM CLK EXT INDEX PLL Fref LOCK Vlogic DETECTOR OUT FILTER IN FILTER COMP CSA INPUT Rsense OUTPUT C gm COMP GATE DRIVE I LIMIT SET CENTER TAP I/O I I I I I O I O I O I O I/O I I/O I I Function Rising edge will initiate start-up. A Braking rountine is started when this input is brought low. A low to high transition on this pin increments the Output State Sequencer. Clock Frequency for the system timer/counters. External Source of Feedback for the PLL. Reference Frequency for the PLL. High when the PLL is phase_locked. Logic power supply. Output of Frequency/Phase Detector. Filter Input. Filter output and compensation. Input to the Current Sense Amplifier. Output C connection for the Motor Current Sense Resistor to ground. DMOS Half Bridge Output and Input C for Bemf sensing. A series RC network to ground that defines the compensation of the Transconductance Loop. Drives the Gate of the External P Channel DMOS Driver for Higher Power Applications. This pin must be grounded if an external driver is not used. A voltage applied to this pin, in conjunction with the value for the external Motor Current Sensing resistor, defines the maximum Motor Current. Motor Center Tap used for differential BEMF sensing. If the center tap of the Motor is not brought out, a virtual center tap is integrated and available at this pin. A resistor connected to this pin sets the Voltage Slew Rate of the Output Drivers.
44
SLEW RATE
I
ELECTRICAL CHARACTERISTICS (Refer to the test circuit, unless otherwise specified.)
Symbol POWER SECTION VPower R DS(on) Io(leak) VF dVo/dt Im(max) Motor Supply Output ON Resistance Output Leakage Current Body Diode Forward Drop Output Slew Rate Motor Current Limit (Note 1) Im = 2.0A R slew = 100K R s = 0.33 Ilim Gain = 0 Ilim Gain = 1 ILIMSET = 5V Ilim Gain = 0 V33 = 0V, V38 = 5V TBD TBD 5 0.30 0.75 0.38 TBD TBD Tj = 25C Tj = 125C 10.5 12 0.25 13.5 0.33 0.50 1 1.5 V mA V V/s A/V A/V mA Parameter Test Condition Min. Typ. Max. Unit
Igt
Gate Drive for Ext. Power DMOS Shut Down Temperature Recovery Temperature Hysteresis Early Warning Temperature Current Sense Amp Input Bias Current Current Sense Amp Voltage Gain Center Tap Input Impedance
Tsd Thys Tew Isnsin GV ZinCT 4/35
150 30 Tsd-25
180
C C C
10 3.8 4 30 4.2
A V/V K
L6238
ELECTRICAL CHARACTERISTICS (Continued)
Symbol LOGIC SECTION VinH VinL IinH IinL VoutL VoutH Fsys ton toff tseq Fshift tos tsettle tstrobe twait tds tdh tsd tcd tsd ttsd twrs tscr tcsw Input Voltage Input Current -1 Output Voltage System Clock Frequency Clock ON Time Clock OFF Time Time Between Rising Edges Clock Frequency Operating Set-up Time Enabling Settling Time Strobe Pulse Width Disable Wait Time Data Setup Time Data Hold Time Strobe to Data Prop. Delay Clock to Data Prop. Delay Data I/O Activation Delay Data I/O Tri State Delay Write to Read Set-up Time Strobe to Clock Time (Read Mode) Clock to Strobe Time (Write Mode) Static Phase Error Capacitor Charge Voltage Source Current Delay Timer Low Trip Threshold Storage Capacitor Output Voltage Blocking Diode Leakage Current Charge Pump Frequency 300 RT = 50K TBD 0.5 TBD 20 10 1.8 TBD 9.5 (*) (*) (*) 50 50 40 40 100 10 100 100 100 80 50 50 50 Vsink = 2mA Vsource = 2mA 0.5 4.5 8 20 20 1 2 TBD 12 TBD TBD 1 V V A mA V V MHz ns ns s MHz ns ns ns ns ns ns ns ns ns ns ns ns ns Parameter Test Condition Min. Typ. Max. Unit
SEQUENCE INCREMENT SERIAL PORT TIMING Note: Cload(data I/O) = 50pF;
PHASE LOCK LOOP SECTION Tphse Vchrg Iout3 VThres Vout9 Vleak Fcp 20 TBD s V mA V V A KHz BRAKE DELAY SECTION
CHARGE PUMP
(*) These parameters are a function of Cload.
5/35
L6238
FUNCTIONAL DESCRIPTION 1.0 INTRODUCTION 1.1 Typical Application In a typical application, the L6238 will operate in Figure 1: Stand Alone Configuration conjunction with the L6243 Voice Coil Driver as shown in Fig. 1. This configuration requires a minimum amount of external components while providing complete stand-alone operation.
6/35
L6238
1.2 Input Default States Figure 2: Input Structures Figure 3: Input Logic
FUNCTION PORT DIS STROBE PORT CLK R/W DATA I/O EXT/INT FREF ENABLE LIN OUTPUT ENABLE RUN/BRAKE SEQ INCR SYS CLOCK EXT INDEX PLL FREF
CONFIGURATION PULL-UP PULL-DOWN PULL-UP PULL-UP PULL-UP PULL-DOWN PULL-DOWN PULL-DOWN PULL-DOWN PULL-UP PULL-DOWN PULL-UP PULL-UP PULL-UP
signals. Although not shown, SEQUENCE INCREMENT and Sequence Increment also form an OR function, with the resultant output signal called Sequence Increment. 1.4 Modes of Operation There are 5 basic modes of operation. 1) Tristate When Output Enable is low, the output power drivers are tristated. 2) Start-Up With Output Enable high, bringing Run/Brake from a low to a high will energize the motor and the system will be driven by the Fully-Integrated StartUp Algorithm. A user-defined Start-Up Algorithm, under control of a MicroProcessor, can be achieved via a serial port and/or external control pins. 3) Run Identified by the Lock signal, Run mode is achieved when the motor speed (controlled by the Internal PLL) reaches the nominal speed within a predefined phase error. 4) Park When Run/Brake is brought low, energy to park the heads may be derived from the rectified Bemf. The energy recovery time is a function of the Brake Delay Time Constant. In this state, the quiescent current of the device is minimized (sleep mode). 5) Brake After the Energy Recovery Time-Out, the device is in Brake, with all lower Drivers in full conduction. During a power down, the Park Mode is triggered, followed by a Dynamic Brake. There are two mutually exclusive conditions which may be present during the Tristate Mode (wake up):
7/35
Figure 2 depicts the two possible input structures for the logic inputs. If a particular pin is not used in an application, it may either be connected to ground or VLOGIC as required, or simply left unconnected. If no connection is made, the pin is either pulled high or low by internal constant current generators as shown A listing of the logic inputs is shown with the corresponding default state. 1.3 Naming Convention In order to differentiate between the various types of control and status signals, the following naming convention is used. BOLD CAPITALS - Device pins. Italics - Serial port control and status signals. Three input signals form a special case. Referring to figure 3, the RUN/BRAKE input pin and the Run/Brake control signal form a logical AND function, while OUTPUT ENABLE and Output Enable form an OR function. The outputs signal names, in Bold Lower case labeled Run/Brake and Output Enable will be used when referring to these
L6238
a)the spindle is stopped. b)the system is still running at a speed that allows for resynchronization. In order to minimize the ramp up time, the microcontroller has the possibility to: check the SPIN SENSE pin, (which toggles at Figure 4: State Diagram the Bemf zero crossing frequency) enable the power to the motor based on the previous information. Otherwise the uP may issue a Brake command, followed by the startup procedure after the motor has stopped spinning.
R unB rk = 0 Out En a = 0 Se qI nc = X
A uto St art -up Fr om An ywh ere Au to /Ext = 0 H old for "A lig n & G o" E na ble d Di sa ble d
B ra ke W/M ask
RunBrk = 1
R unB rk = 0 & Out En a = 0 Hol d & wa it fo r d eci sio n
Run Br k = 1 O utE na = 0 Tr i- sta te W/M ask OutEna = 1 OutEna = 0 Seq In c = 0 S eq Inc = 1 R unB rk = 1 Ou tEn a = 0 Tr i-s tat e W /Ma sk
Po wer on Re set
Ru nBr k = 1 O ut Ena = 1
Ru nB ra k e=
0
=1
RunBrk = 0
A cti on a cro ss li ne in cre me nts s equ enc er
= na tE Ou 0
= na tE Ou
1
Ru nB ra ke
Run W/Mask O utE na = 1 & Ru nBr k = 1 RunBrk = 0
Se qI nc = 0 Se qIn c = 1
R un Wo/ Mas k RunBrk = 1 OutEna = 1
=1 rk 0 nB a = Ru tEn u O
Ho ld fo r "R esync"
S tuc k Rot or ( hol d)
Ho ld fo r " Al ign & G o" [Align to Phase # 1]
Out En a = 1 & R unB rk = 0
0 a= En =0 ut O tEna =0 Ou na tE Ou
Ou Ou tEn tE a= na 0 Ou =0 tE na =0
RunBrk = 1
Zc No St art "R esync" (Get 1st Zc) Zc Reset = S trR tr = 0
Al ig n=
0
Sta rt " Al ign & G o" Align = 1 [Align to Phase # 3]
Zc No
G o=
0
Re syn c = 1 Re lea se mi n ma sk
S trR tr = 0 (G Zc et 2 Rn es d Z et c) = StkRtr = 0 Mono = 0
A lig n = S eq ncr .
1 o= G
Run
8/35
L6238
2.0 STATE DIAGRAMS 2.1 State Diagram Figure 4 is a complete State Diagram of the controller depicting the operational flow as a function of the control pins and motor status. The flow can be separated into four distinct operations. Figure 5: Align+Go 2.2 Align + Go Figure 5 represent the normal flow that will achieve a spin-up and phase lock of the spindle motor. Upon power up, the controller first checks to determine if the motor is still spinning. This "Hold For Resync" decision block will be discussed later.
RunBrk = 1 OutEna = 0 Power on Reset Hold for "Res ync" RunBrk = 0 Hol d & wait for decision RunBrk = 1 OutEna = 1 OutEna = 0
Hold for "Ali gn & Go" [Align to Phase # 1]
OutEna = 0 & RunBrk = 0
=0 na 0 = tE na Ou tE Ou =0 na tE Ou
RunBrk = 1
Al ign =
0
Start "Align & Go" Align = 1 [Align to Phase # 3]
Go =
0
Align = Seqncr. Go = 1 Run
9/35
L6238
Assuming the motor is stationary, with Output Enable high and Run/Brake low, the controller is in the "Hold for Align & GO" state. When Run/Brake is brought high, the motor is in align mode with Phase 1 active (Output A high and Output B low). Align is a zero. After the align time-out (user-programmable), the Align bit goes high and the sequencer double increments the outputs to Phase 3 (Output B high and Output C low). After the next time-out, the controller enters the Go mode, with the sequencer automatically incrementing the output phase upon detection of the motor's Bemf. Never command an Align & Go unless a reference signal is present at PLL FREF, since this is the signal that determines the length of time that phase 1 remains active. If Run/Brake is brought low, (or if the 5V supply is removed) the controller will revert to "Hold for Align & GO" and the serial port will be reinitialized. In order to prevent an erroneous restart condition, it is necessary that Run/Brake be held low until the motor has completely stopped. Once the motor has stopped, Run/Brake may be brought high for a complete Align & Go Start-Up routine. Figure 6: Resync.
2.3 Resynchronization If power is momentarily lost, the sequencer can automatically resynchronize to the monitored Bemf. This resychronization can either occur whenever Output Enable is first brought low then high or if the Logic Supply is momentarily lost. Referring to figure 6, the "Hold for Resync" state is entered upon POR (Power On Reset) or whenever Output Enable is brought low. The controller leaves this state and enters "Start Resync" when Output Enable is high. If zero crossings are detected, the sequencer will automatically lock on to the proper phase and bring the motor speed up to Phase Lock. This resynchronization will take effect with the motor speed running as low as typically 30% of it's nominal value. Never command an Align & Go while the motor is spinning. Always initiate a resync first or initiate brake mode and allow the motor to spin down.
1 r k= nB =0 Ru t Ena Ou
Power on Reset
Hold for "Resync"
Ou t Ou Ena = tE na 0 =0 Ou tE na =0
Zc No Start "Resync"
Zc No
Resync=1 Release min mask (Get 2nd Zc) Zc Reset = Run
10/35
(Get 1st Zc) Zc Reset =
OutEna=1
L6238
2.4 Stuck Rotor/Monotonicity Refer to figure 7. In order to alert the microprocessor of fault conditions, two bits are available in the Serial Port's Status Register.
1. Stuck Rotor If the controller enters the Go mode after the Double Align, Bemf must be detected within 419ms when using a system clock frequency of 10MHz. If this condition is not met, the outputs will be tristated and set this bit to a zero. The controller enters the "Stuck Rotor Hold" state.
Figure 7: Stuck Rotor/Monotonicity.
O ut En a = 1 & Ru nB r k = 1
2. Mono When the motor spins up normally, the resultant S P IN SENSE pulses rise in frequency in a monotonic pattern. Any fault condition that would cause a rapid decrease in the SPIN SENSE frequency would be detected by internal counters setting the MONO bit low and forcing a Brake condition
2.5 External Sequencing Although the user-defined Start-Up Algorithm is flexible and will consistently spin up a motor with minimum external interaction, the possibility exists where certain applications might require complete microprocessor control of start-up. The L6238 offers this capability via the SEQUENCE INCREMENT input. Referring to figure 9, with Output Enable and Run/Brake low, the controller is in the "Hold and Wait for Decision" state. If the SEQUENCE INCREMENT pin is brought high during this state, the Auto StartUp Algorithm is disabled and the sequencer can be controlled externally. When Output Enable and Run/Brake are brought high, the sequencer is incremented every time that the SEQUENCER INCREMENT pin is first brought low and then high. During the time that this pin is high, all Bemf information is
S tu c k Ro t or (h ol d) =0 Mono = 0
Figure 8: Ext. Sequence.
RunBrk = 0 OutEna = 0 SeqInc = X
StkRtr
R un
Auto Start-up Enabled Disabled
Brake W/Mask
RunBrk = 1
OutEna = 0 & RunBrk = 0
RunBrk = 1 OutEna = 0
RunBrk = 0
Power on Reset
Acti on across line increments sequencer
SeqInc = 0 Hold & wait for decision 0 = na tE Ou e= Tri-state W/Mask SeqInc = 1 OutEna = 1 OutEna = 0 RunBrk = 1 OutEna = 0 1 = na tE Ou Tri-state W/Mask
Ru nB ra k e=
Ru nB rak
1 rk = 0 nB Ru En a = t Ou
RunBrk = 1 OutEna = 1
0
1 Run W/Mask
SeqInc = 0 SeqInc = 1 RunBrk = 0
Hold for "Resync"
Run Wo/Mask RunBrk = 1 OutEna = 1
Hold for "Align & Go"
OutEna = 1 & RunBrk = 0
11/35
L6238
masked out, and when it is low, the Bemf information can be detected normally. When the motor has reached a predetermined speed, the SEQUENCE INCREMENT pin can be left low and the L6238 Motor Control logic will take over and automatically bring the motor into Phase Lock. 3,0 START-UP ALGORITHMS 3.1 Spin-Up Operation The spin operation can be separated into 3 parts: 1) Open Loop Start-Up - The object is to create motion in the desired direction so that the Bemf voltages at the 3 motor terminals can provide reliable information enabling a transition to closed loop operation. 2) Closed Loop Start-Up - The Bemf voltage zerocrossings provide timing information so that the motor can be accelerated to steady state speed. 3) Steady-State Operation - The Bemf voltage zero-crossings provide timing information for precision speed control. The L6238 contains features that offer flexible control over the start-up procedure. Either the onFigure 9: Auto Start Profile board Auto-Start Algorithm can be used to control the start-up sequence or more sophisticated extemal start-up algorithms can be developed using the Serial Port and key control/sense functions brought out to pins. 3.2 Auto-Start Algorithm The Serial Port Control Bit Auto/Ext (Refer to Table 2), controls the start-up mode. The power up default state is a logic high which selects the AutoStart Mode. When Run/Brake is low, the L6238 is in brake mode, and the Auto-Start Algorithm is reset. In the brake mode, all of the lower DMOS drivers are ON, and the upper drivers are OFF. Note that Run/Brake should be brought low for a period exceeding the value selected for the brake delay time in order to initialize the brake delay circuit. The Auto-Start Algorithm is based on an Align & Go approach and can be visualized by referring to Figure 9. Shown are the Output Enable and Run/Brake control signals, sequencer output with the resultant output phases, and the Align and Go status bits. The times labeled Tl and T2 are two
Tasd <1> 0 0 1 1
Tasd <0> 0 1 0 1
Ta = T1 0.178 s 0.356 s 0.533 s 0.711 s
T2 0.533 s 1.067 s 1.600 s 2.133 s
Tg 0.711 s 1.422 s 2.133 s 2.844 s
Note: PLL Reference Frequency = 90Hz
12/35
L6238
delays that are 25% and 7S% respectively of the total delay selected by the Auto-Start Delay Control Bits. The times labled T1 and T2 are the times associated wim the Align and Go status bits. Typical delays associated with these times for a PLL reference frequency of 90Hz are shown in the figure. Referring to figure 9, the following is the sequence of events during Auto-Start: Alignment Phase - Output Stage is energized to phase 1 with OUTPUT A high and OUTPUT B low for T seconds. - The intemal sequencer double increments the output stage to Phase 3 for T2 seconds. If phases 1 or 3 are high torque states, the motor should become aligned. - During the alignment phase, the SEQ INCREMENT signal is ignored. Go Phase - The internal sequencer double increments the output stage to State 5, which should produce torque in the desired direction. - with SEQ INCREMENT held low, the sequencer is now controlled by the Bemf zero crossings, and the motor should ramp up to speed. If backward rotation is detected, a status bit in the serial port will be set, and the L6238 will revert to the brake mode. - If a stuck rotor condition exists, the Stuck Rotor Status bit is flagged, but no action is taken. If though during a stuck rotor condition, the time out due to the backwards rotation occurs, the L6238 will revert back to the brake mode. 3.3 Externally Controlled Start-Up Algorithms Enhanced Start-Up Algorithms can be achieved by using a uProcessor to interact with the L6238's control and status signals. The uProcessor needs to be heavily involved during Open Loop Start-Up. The L6238 has the ability to transition to Closed Loop Start-Up at very low speeds, reducing the uProcessor task to monitoring status rather than real time interaction. Thus, it is a perfect application for an existing uProcessor. To allow control via an external means, the Auto/Ext Control Bit in the Serial Port must be set low. This disables the internal Auto-Start Algorithm. The following control and status signals allow for very flexible algorithm development: SEQ_INCR A low to high transition at this input is used to increment the state of the power output stage. It is useful during start-up, because the Processor can cycle to any desired state, or cycle through the states at any desired rate. When held high, it inhibits the BEMF zero crossings from incrementing the internal sequencer. SPIN SENSE This output is low until the first detected Bemf zero crossing occurs. It then toggles at each successive zero crossing. This signal serves as a motion detector and gives useful timing information as well. LOCK A high denotes that the phase error between the PLL reference and the feedback signals is within the programmed threshold. This signal is updated once per revolution.
Seq Reset This bit is used to reset the output stage to the first state.
3.4 Start Up Approaches Align & Go Approach The Align & Go approach provides a very time efficient algorithm by energizing the coils to align the rotor and stator to a known phase. This approach can be achieved via the Seq Reset, or by sequencing SEQ INCR. SPIN SENSE can be monitored to assure that motion occurred. Once ample time is given for alignment to occur, SEQ INCR can be double incremented, and the SPIN SENSE pin can be monitored to detect motion. When SEQ INCR is pulled low, control is transferred to the internal sequencer, and the L6238 finishes the spinup operation. If no motion is detected, SEQ INCR can be incremented to a different phase and the process can be repeated. The alignment phase may cause backward rotation, which on the average will be greater than the Stepper Motor approach. The Auto-Start algorithm described earlier is an Align & Go approach. The main advantages of the integrated Auto-Start are that the uP is not involved real-time, and there are a minimum of interface pins required to the spindle control system. Stepper Motor Approach This approach minimizes backward rotation by sequencing SEQ INCR at an initial rate that the rotor can follow. Thus, it is driven in a similar fashion to a stepper motor. The rate is continually increased until the Bemf voltage is large enough to reliably use the zero-crossings for commutation timing. SEQ INCR is held low, causing control to be passed to the L6238's internal sequencer as in the Align & Go approach. The Stepper Motor approach takes longer than the Align & Go approach because the initial commutation frequency and subsequent ramp rate
13/35
L6238
Figure 10: Phase Detector State Diagram.
must be low enough so that the motor can follow without slipping. This implies that to have a reliable algorithm, the initial frequency and ramp rate must be chosen for the worst case motor under worst case conditions. 4.0 DIGITAL PLL MOTOR SPEED CONTROL 4.1 Phase Detector The internal Phase/Frequency Detector of the PLL has two inputs: - reference input (Fref) - feedback input (Fmtr) The feedback Input is multiplexed between the internal Bemf Zero Crossing Detector and an externally provided sync pulse (EXT INDEX)
14/35
Shown in figure 10 is the classical state diagram for a phase detector along with waveform examples. Positive phase is defined as when the reference falling edge occurs before the falling edge of Fmotor and the motor speed must be increased. Negative phase is just the opposite, requiring a slowing of the motor speed. As an example, the top four waveforms in figure 10 represent a positive phase condition. In this case the "up" signal would go low since the reference signal went low before the appearance of a negative transition of fmotor. The falling edge of fmotor causes the "up" signal to revert back to a high. The period while the "up" signal is in a low state is a function of the phase difference.
L6238
Figure 11: Logic Block Diagram.
4.2 Counter Section Figure 11 is a block diagram of the counter section of the PLL along with the phase detector. The phase detector provides up and down signals that are used to control the direction and counting period of two 8 bit counters. Two counters are used to provide both coarse and fine phase error information. The coarse counter operates to bring the phase error into a finite window, while the fine counter with it's higher resolution controls the phase jitter to typically 5s. As an example, during a positive phase measurement, the counters are reset to 10000000 which is the middle of their measurement range corresponding to zero degrees phase error. The falling edge of Fref, in conjunction with the "up" signal, causes the fine counter to then start counting up. The coarse counter is inhibited by the fine counter until the fine counter has reached it's maximum count. The falling edge of Fmtr causes the counters to stop counting and the bits in the fine and course counters are then latched into their respective latches. The counters are then reset to 10000000 in anticipation of the next phase measurement. The operation of the counter section during spinup and phase lock can be described in three phases: 1) Initial Spin-Up - At start-up the PLL will inher-
ently bring the motor speed "in line" with the reference frequency.The phase detector is initialized at power up to force the counters to start counting up. Since there will be many more Fref. vs Fmtr falling edges at start-up, the width of the "up" pulse will be wide. The fine counter will reach it's maximum count and send an enable pulse to the coarse counter causing it to start counting. After 127 counts, the coarse counter also reaches it's maximum count. At the end of the "up" pulse, it's rising edge loads the outputs of the Coarse and Fine counters into corresponding latches. Thus the latches are updated once-per-rev with a binary number that corresponds to the measured phase error. This count will be converted via a Digital to Analog Convertors (DAC) into a speed Command Voltage, which at start-up will be the maximum as set by the ILIM SET voltage. 2) Overshoot - As the motor speed increases close to the reference, the coarse counter comes out of compliance and decreases it's count as the phase difference becomes smaller. The fine counter then takes over when the phase is in a certain range. A certain amount of phase overshoot will take place as the motor passes though zero phase difference due to the closed loop system response characteristics. This will cause the counters to count down to "slow" the motor down until the phase difference is minimal.
15/35
L6238
Figure 12: Coarse and Fine DAC's.
3) Phase Lock - After a brief settling time, typically 1-2 seconds after spin-up, the counters will alternately count up and down as required to maintain the phase difference to be as close to minimum as possible. The counter outputs at this time should be "hovering" around 10000000. The outputs of the two DACs are sent to latches that store the digital representation of the measured phase error. This information is then bussed to the DACs. 4.3 Coarse/Fine DACs Two DACs are used to convert the digital phase error information into an analog voltage that can Table 2
Fsystem Clock 8MHz 10MHz 12MHz 16/35 Fcoarse 15.6KHz 19.5KHz 23.4KHz Phase LSB Coarse 64.1s 51.3s 42.7s
be used to command the output driver's current. In figure 12, the two 8-bit digital error signals are used to switch in 256 possible voltages derived from a precision Band-Gap reference. The same resistor ladder string is used for the Coarse and Fine DACs. The outputs of the DACS are then sent to buffer stages and added together via a summing amplifier. 4.4 Transfer Functions Figure 13 represent the Output Voltage vs Phase Error for the Coarse and Fine DACs depicting the resolution that is achievable. Table 2 shows examples of the resolution of both
(Range) Coarse 16.3ms 13.1ms 10.9ms
Ffine 1.0MHz 1.25MHz 1.5MHz
Phase LSB Fine 1.0s 800ns 667ns
(Range) Fine 255s 204s 170s
L6238
Figure 13: Coarse/Fine DAC's Output Graphs.
DACs as a function of the system clock repetition rate. Fcoarse is the system clock divided by 512, while Ffine divides the clock by 8. This gives for example, Coarse and Fine LSB's of 51.3us and 800ns respectively for a system clock repetition rate of 10MHz. Therefore the best phase jitter that could be achieved as a function of the counter resolution is 800ns. The dynamic range of each counter is also shown in the table. It can be seen that the ratio of Fine to Coarse counts is 64. The summing amplifler divides the Fine DAC buffer output voltage by a factor of 16. Therefore there is a 4:1 ratio of Fine to Coarse gain. This results in a Speed Control Loop that is fairly easy to compensate with excellent transient response. The output of the PLL Detector is fed to a general purpose. filter amplifier that is used to compensate the Speed Control Loop. The filter amplifier output stage has been carefully designed to limit the compliance voltage to a value that tracks the Ilim Set voltage, thus limiting the amount of overshoot and enhancing the transient response of the loop. 4.5 PLL Detector Output Figure 14 is a graph of the typical DETECTOR
OUTPUT voltage as a function of the detected phase difference as measured on production material. The change of the gain slope is apparent around the zero phase difference point. With the spindle motor at phase lock, the DETECTOR OUTPUT voltage is typically 2.0, equivalent to the internal Virtual Ground level. Figure 14: Vdetector Output vs Phase Error.
17/35
L6238
5.O MOTOR DRIVER 5.1 Output Stage The output stage forms a 3-phase, full wave bridge consisting of six Power DMOS FETs capable of 2.5 amps. Higher output currents are allowed for brief periods. Output Power exceeding the stand-alone power dissipation capabilities of the L6238 can be increased with the addition of an external P-FET. Table 3 is a reference diagram that lists the parameters associated with 8-pole motors operating at 3600 and 5400 RPM. Figure 15 represents the waveforms associated with the output stage. The upper portion of figure 15 shows the flow of current in the motor windings for each of the 24 phase increments. A rotational degree index is shown as a reference along with a base line to indicate the occurrence of a zero crossing. The 3 output waveforms are actual digitally reproduced voltage signals as measured on samples. A typical sequence starts when the outputs switch states. Referring to figure 15, during phase 1, output A goes high, while output B is low. During this Table 3. phase, output C is floating, and the Bemf is monitored. The outputs remain in this state for 60 electrical degrees as indicated by the first set of dashed lines. After this period the output switches to phase 2 with output A high and C low with the Bemf amplifier monitoring output B. In order to prevent commutation current noise being detected as a false zero crossing, a masking circuit automatically blanks out all incoming signals as soon as a zero crossing is detected. When the next commutation occurs an internal counter starts counting down to set the time that the masking pulse remains The counter is initially loaded with a number that is equal to period that is always 25% of the previous phase period or 15 electrical degrees. This time-out of the masking pulse shown for reference at the bottom of figure 16. Thus the actual masking period is the total of the time from the detected zero crossing to the commutation, plus 25% of the previous period. The mask pulse operation is further discussed in section 5.6, Slew Rate Control. After the masking period, the Bemf voltage at output B is monitored for a zero crossing. Upon detection of the crossing the output is sequenced after 30 electrical degrees insuring maximum
Rotational Speed Rotational Freq. Rotational Period Electrical Period Phase Period
3600 rpm 60Hz 16.667 ms 4.167 ms 694.5 s
5400 rpm 90Hz 11.111 ms 2.778 ms 463.0 s
18/35
L6238
Figure 15: Brake Delay.
19/35
L6238
torque. The spin sense waveform at the bottom of the figure indicates that this output signal toggles with each zero crossing. 5.2 Brake Delay When Run/Brake is brought low, a brake is initiated. Referring to figure 16, SWI is opened and the brake delay capacitor, Cbrake, is allowed to discharge towards ground via Rbrake. At the same time, switches SW2 through SW7 bring the gates of the output FETs to ground halting conduction, causing the motor to coast. While the motor is coasting, the Bemf is used to park the heads. When Cbrake reaches a voltage that is below the turn ON threshold of Q I, Switches SW8, 9 and 10 bring the gates of the lower drivers to Vbrake potential. This enables the lower FETs causing a braking action. This braking action also occurs if the logic supply is lost. The analog supply is not Figure 16: Brake Delay. monitored in the L6238 since the L6243 already monitors this voltage and initiates a Park function when this supply drops to a predetermined level. If multiple logic supplies are used in the application, all logic signals to the L6238 including the reference and clock signals should be buffered with gates powered by the same supply as the L6238 in order to prevent erroneous operation. This would occur, for example, if the 5V supply to the controller were lost while 5V were still present at one of the logic pins. This would partially power the chip, causing unpredictable operation. 5.3 Charge Pump The charge pump circuitry is used as a means of doubling the analog supply voltage in order to allow the upper N-channel DMOS transistors to be driven like P-channel devices. The energy stored in the reservoir capacitor is also used to drive the
20/35
L6238
Figure 17: Charge Pump Circuit.
lower drivers in a brake mode if the analog supply is lost. Figure 17 is a simplified schematic of the charge pump circuitry. A capacitor, Cpump, is used to retrieve energy from the analog supply and then "pumps" it into the storage capacitor, Cresvr. An internal 300kHz oscillator first turns ON Q2 to quickly charge Cpump to approximately the rail voltage. The oscillator then turns ON Ql while turning OFF Q2. Since the bottom plate of Cpump is now effectively at the rail potential, Cresvr is charged to ~ twice the rail voltage via D2. A zener referenced series-pass regulator supplies a voltage, Vbrake, during brake mode. 5.4 Output Current Control The output current is controlled in a linear fashion via a transconductance loop. Referring to figure 18, the sourcing FET of one phase is forced into full conduction by connecting the gate to Vpump, while the sinking transistor of an appropriate phase operates as a transconductance element. To understand the current control loop, it will be assumed that Q2 in figure 18 is enabled via SW2 by the sequencer. During a run condition, the current in Q2 is monitored by a resistor R4 connected to the Rsense input. The resulting voltage that appears across R4 is amplified by a factor of four by A3 and is sent to A2 where it is compared to the PLL error signal. A2 provides sufficient drive to Q2 in order to
maintain the motor speed at the proper level as commanded by the PLL. During initial start-up, the error signal from the output of the PLL Phase/Frequency Detector will be at compliance in order to quickly bring the motor up to correct speed. The motor current during this condition can be safely limited to a predetermined value by applying a voltage to the ILIM SET input. The voltage at this input is buffered by A1 and sent to multiplexer, SWl. The output voltage of the multiplexer, Vclmp, is used to control the maximum non-inverting input voltage for amplifier A2. This multiplexer also receives a voltage that is 1/2 the ILIM SET value via a resistor divider connected to the buffer. Control bit llim Gain determines which voltage is available at the output of the multiplexer and allows a 2:1 change in the output current limit under software control. For example, if the Ilim Gain control bit is set high, and 3.3V were applied to the ILIM SET input, then Vclmp would equal 1.65V. Since A3 has a voltage gain of 4, this would translate to a maximum sensed voltage at the Rsense input equal to 0.41V. If Rslew were selected to be 0.33 , then the maximum output current would be limited to ~1.25A. By setting the Ilim Gain control bit low, Vclmp now equals ILIM SET, and the clamped sensed voltage at the Rsense input would be doubled to 0.82V, allowing a maximum of 2.5A at the output.
21/35
L6238
Figure 18: Linear Control Loop.
5.5 Transconductance Loop Stability The RC network connected to the Compensation pin provides for a single pole/zero compensation scheme. The pole/zero locations are adjusted Figure 19: Control Loop Response.
such that a few dB of gain (typ. 20dB) remains in the transconductance loop at frequencies higher than the zero. The inductive characteristic of the load provides
22/35
L6238
the pole necessary for loop stability. Thus the loop bandwidth is actually limited by the motor itself. Figure 19 shows the complete transconductance loop including compensation, plus the response. The Bode plot depicts the normal way to achieve stability in the loop. The pole and zero are used to set a gain of 20dB at a higher frequency and the pole of the motor cuts the gain to achieve stability. Loop instability may be caused by two factors: 1)The motor pole is too close to the zero. Referring to figure 20, the zero is not able to decrement the shift of phase, and when the effect of the pole is present, the phase shift may reach 180 and the loop will oscillate. To rectify this situation, the pole/zero must be shifted at lower frequencies by increasing the compensation capacitor. Figure 20: Motor Pole. though the gain decrease at a rate of 40dB/decade, the phase does not reach 180 of shift. If the gain at higher frequencies is sufficiently high, the double pole slope of 40dB/decade can cause the phase shift to reach 180, resulting in oscillation. Figure 22 is a Bode plot showing how to correct this situation. The bold line indicates the response with relatively high gain at the higher frequencies. By leaving the pole unchanged and increasing the zero, the response indicated by the dashed lines can be achieved. Figure 22: Correct Compensation.
2)The motor capacitance, CM, itself can interfere with the loop, creating double poles. If the gain at higher frequencies is low, this double pole will not be able to reach a critical value due to it's 40dB/decade slope. Figure 21 illustrates performance with low gain. AlFigure 21: Effect of Cm.
5.6 Slew Rate Control A 3-phase motor appears as an inductive load to the power supply. The power supply sees a disturbance when one motor phase turns OFE and another turns ON because the FET turn-OFF time is much shorter than the L/R rise time. Abrupt FET turn-OFF without a proper snubbing circuit can even cause current recirculation back into the supply. However, the need for a snubber circuit can be eliminated by controlling the turn-OFF time of the FETs.
23/35
L6238
Referring back to figure 18, the rate at which the upper and lower drivers turn OFF is programmable via an external resistor, Rslew connected to the SLEW RATE pin. This resistor defines a current which is utilized internally to limit the voltage slew rate at the outputs during transition, thus minimizing the load change that the power supply sees. Figure 23 is a plot of the slew rate that will be obtained as a function of the resistor connected to the SLEW RATE pin. The voltage at the this pin is typically 2.4V. To insure proper operation the range of resistor values indicated should not be exceeded and in some applications values near the end points should be avoided as discussed below. Low Values of Rslew - If a relatively low value of Rslew is selected, the resultant fast slew rate will result in increased commutation cross-over current, higher EMI, and large amount of commutation current. This last case can cause voltage spikes at the output that can go as much as lV below ground level. This situation must be avoided in this integrated circuit (as in most) since it causes unpredictable operation. High Values of Rslew - Higher values of Rslew result of course in slow slew rates at the outputs which is, under most conditions, the desired case since the problems associated with fast rates are reduced. The additional advantage is lower acoustical noise. Problems can occur though if the slew rate for a given application is too slow. Figure 5-10 is an oscillograph taken on a device that had a fairly large value for Rslew and failed to spin up and phase Figure 24: Effect of Slow Slew Rate. Figure 23: Output Voltage Slew Rate vs Rslew.
lock a motor. The problem manifests itself as the motor begins to spin up. At lower RPMs, the Bemf of the motor is relatively small resulting in higher amounts of commutation current. In figure 24, the upper waveform is the voltage appearing at OUTPUT relative to the CENTER TAP input. The lower waveform is the actual output of the Bemf amplifier available on special engineering prototypes. The oscillograph was taken just as the problem occured. The period between zero crossings was ~800s resulting in a mask time period of 200s. As can be seen, the excessively long slew rate
24/35
L6238
actually exceeded the mask period and was detected as a zero crossing. This resulted in improper sequencing of the outputs relative to the proper phases and caused the motor to spin down. If the application requires a slow rate of slew at the output, an external network can be connected as shown in figure 25. A resistor, Rl is selected to achieve the desired slew rate when the system is in phase lock. A second resistor, R2, in series with a diode, Dl, is connected between the SLEW RATE pin, and the LOCK output. At start up, the LOCK output is low, and R2 is in parallel with Rl resulting is a faster slew rate. When lock is achieve, the LOCK output is high, and R2 is essentially disconnected from the circuit. 5.7 Ext PFET Driver The power handling capabilities of the 3 phase output stage can be extended with the addition of a single P-Channel FET. Figure 26 shows the Ext FET connection and demonstrates how the L6238 automatically senses the FETs presence. When the voltage at the Gate Drive pin is 0.7V, the output of comparator A3 goes high, removing the variable drive Al from the internal FETs and connects them instead to Vanalog via the commutation switches to facilitate full conduction. The upper FETs drive Figure 26: External P-Fet. Figure 25: Dual Slew Rate.
paths are not shown for clarity. A3 also closes SW2 allowing Al to linearly drive the external PChannel FET Ql via inverter A2. 5.8 Bemf Sensing Since no Hall Effect Sensors are required, the commutation information is derived from the Bemf voltage zero-crossings of the undriven phase with respect to the center tap. The Bemf comparator and associated signal levels are depicted in figure 27. For reliable operation, the Bemf signal amplitude should be a minimum of 60 mV to be properly detected. In order to provide for noise immunity, internal hysteresis is incorporated in the detection circuitry to prevent false zero crossing detection.
25/35
L6238
Figure 27: Bemf Amplifier.
For laboratory evaluation purposes, a simple resistive network as shown in figure 28 can be used to emulate the Bemf of the motor. The actual Bemf zero-crossing is 30 electrical degrees (50% of a commutation interval) away from the optimal switch point. A digital counter circuit measures 50% of the previous interval to determine the next interval's commutation delay from the zero crossing. During the low RPM stages of Figure 28: Bemf Emulator.
start up the long commutation intervals may cause the counter to overflow, in which case 50% of the max count will be less than 50% of the ideal commutation interval. Therefore, the torque will not be optimal until the desired commutation interval is less than the dynamic range of the counter. 6.0 SERIAL PORT
26/35
L6238
6.1 Description The L6238 contains a powerful serial port that may be optionally used to dramatically increase the functionality of the controller without significantly increasing the pin count. The serial port serves two primary functions: 1. Receive Control Information A total of 16 bits of control information can be programmed via the serial port, in addition to the capabilities provided by external pins. By duplicating key serial port control functions at dedicated pins, the L6238 will still provide sufficient motor control for many applications, without the use of the serial port. 2. Provide Status Information Certain status information is available only via the serial port, with additional information available at dedicated pins. 6.2 Block Diagram Figure 29 is a simplified block diagram of the serial port. It consists of a 16-bit shift register, a 16-bit latch, and some control logic. The serial port utilizes 5 pins to communicate with the outside world. They are: Data I/O The data I/O pin enables 16 bits of data to flow in as control or out as status information. Read/Write This pin selects read or write mode. Clock Used to shift data in or out of the serial Figure 29: Block Diagram. port. Disable If multiple controllers are connected for parallel operation, this signal can be used to select communication to a particular port. If the Serial Port is not used, the PORT DISABLE pin should be tied high. Strobe The read operation is transparent. When the strobe is high, the data on the status bus flows through to the serial register. In a write operation, the loading of the control bits into the parallel control latch is an edge-triggered operation occurring on the rising edge of the strobe. 6.3 Functional Truth Table Table 4 defines the states for the disable and R/W functions. If the disable pin is asserted high, the Data I/O pin is tristated to a High-Impedance state. The R/W pin determines whether the Data I/O pin is an input or an output. The AC operating parameters of the serial port are defined in the Electrical Specifications. Table 4: Truth Table.
Dis 0 0 1 R/W 0 1 X Function Write to Serial Port (Data I/O = Input) Read to Serial Port (Data I/O = Output) Chip Disabled (Data I/O = Hi Z)
6.4 Timing Diagrams
27/35
L6238
Figure 30 is the timing diagram for writing to the serial port. This diagram indicates the typical waveforms at the serial port and how they relate to one another when the PORT DISABLE pin is used. Two consecutive write cycles with key timing parameters are illustrated. To initiate the write cycle, the STROBE and R/W signals are first brought low. After a minimum setup time, Tos, the PORT DISABLE pin is set low. The clocking of the data can begin after a minimum settling time, T settle has passed. The data is clocked into the register on the falling edge of the PORT CLOCK. After the 16th clock cycle and wait time Tcsw a strobe signal causes the data to be transferred to the 16-bit latch. Additional timing parameters that are relevant concern the timing of the clock signal relative to the data stream. The time Tds is the data set up Figure 30: Write Timing Diagram. time, where the data must be stable before the falling edge of the clock. The Data Hold time, Tdh, is the minimum time that the data must be valid after the rising edge of the clock pulse. The waveforms associated with reading from the serial port are similar to the write mode. The main difference is in the timing of the strobe pulse. Since there is a single port for both read and write, the strobe signal, in conjunction with the R/W signal insures proper data stream flow. Referring to figure 31, the read mode is initiated by first asserting the R/W line high, while holding the strobe line low. The PORT DISABLE pin is then brought low. A pulse is now sent to the strobe pin that transfers the data on the Status Bus to the Shift Register. The falling edge of the strobe cannot occur earlier than the minimum settling time, Tsettle. The data is shifted out on the
Figure 31: Read Timing Diagram.
28/35
L6238
I/O port at the falling edge of the port clock. Figure 32 shows the proper waveforms that are applied to the appropriate serial port signal pins during a read to write transition. The strobe input in this case is held low. Time Ttsd is the Data I/O Figure 32: Read to Write Diagram. Tri State Delay. Figure 33 displays the timing diagram during a write to read operation. 6.5 Control Register
Figure 33: Write to Read Diagram.
29/35
L6238
Table 5 lists the 16 available control bits along with a description and power up default values. Certain bits are replications of their external pin counterparts while others provide the means to "customize" the controller to match a unique application and are described in further detail below. thresholds cover the range between 6.4 and 51.2 us as shown in Table 7.
Auto Start Delay - Table 8 lists the delays available for the Align & Go start up algorithm with values for 90Hz and 60Hz applications.
6.6 Status Register The serial port also contains 16 bits that give useful information about the inner workings of the controller. Table 9 provides a functional description of each of the status bits. The status bits prove valuable during certain situations with one example highlited below.
Phase Delay - A more efficient torque profile can be achieved by advancing the commutation angle to compensate for the L/R time constant. There are 3 bits in the serial port that are used to program the delay between the zerocrossing and the commutation point. Thus the user has the ability to use the motor more efficiently by programming the optimal delay. Table 6 is a mapping between the serial ports bits and the commutation delay. In selecting the phase delay, the amount of slew rate introduced must be considered, since the switching is effectively at the 50% points and this delay can be a significant contribution. Lock Threshold - Bits 2 and 3 control the phase error window between the reference and the motor that must be met in order to allow the LOCK signal to go high. Four differenct
Figure 34: Failed Rysync.
Align +Go - These 2 bits can be used to determine if a resync operation was succesful or not. During a commanded resync, these bits will be initially high, and will stay high if the resync was successful. However, figure 34 shows the timing of these 2 bits during an unsuccesful resync where the Go bit goes low 419 ms after the resync command if no Bemf zero crossing is detected.
Tasd <1> 0 0 1 1
Tasd <0> 0 1 0 1
Ta 0.178 s 0.256 s 0.533 s 0.711 s
Tg 0.711 s 1.422 s 2.133 s 2.844 s
Ts 0.419 s 0.419 s 0.419 s 0.419 s
Note: PLL Reference Frequency = 90Hz System Clock = 10MHz.
30/35
L6238
Table 5: Control Register.
Ctrl Bit # 0 Signal Name Control Function Description Determines whether the once-perrevolution signal (used as the motor's feedback for speed) comes from internally generated source or is to be supplied externally as an input. When enabled, passes external PLL fref to Phase Detector Two bits that set the Lock Signal threshold in the Phase Detector Logic 0 = Use Int Speed Fdbk 1 = Use Ext Speed Fdbk 0 = Enable 1 = Disable Refer to Table 7 0 1 1 Not used. Enables Output Drivers. When this signal is used to Tri-State the outputs, it also resets the resynchronization algorithm. This bit along with the OUTPUT ENABLE pin forms a logical AND function. When brought high, initiates the Align and Go algorithm. When low, Brake action occurs after the Brake Delay Timeout. This bit along with the RUN/BRAKE pin forms a logical AND function. Resets the sequencer to Phase 1. Reset when in Brake Mode. Selects either the Internal Auto Start-Up or External Algorithm. Increments sequencer Three bits that set the Delay between the detection of the Bemf zero crossing and the commutation to the next phase. 0 = Required 0 = Enable 1 = Disable 0 1 Default State 0
Ext/Int
1 2 3 4 5
Fref Enable Lock_ Thrsh_0 Lock_ Thrsh_1 Linear Out_Ena
6
Run/Brake
1 = Run 0 = Brake
1
7 8 9 10 11 12 13 14 15
Seq_Reset Auto/Ext Seq_Incr Phase_ Delay_0 Phase_ Delay_1 Phase_ Delay_2 Auto_Str_ Dly_0 Auto_Str_ Dly_1 Ilim_Gain
1 = Reset 0 = Normal 1 = Auto 0 = External 1 = Mask Bemf 0 = Normal Refer to Table 6
0 1 0 1 0 1
These 2 Bits define 4 possible delayes for Auto Start-Up Algorithm.
Refer to Table 8
1 1
Programs the I Limit for either the value set by ILIM SET or /2
0 = Ilimit 1 = Ilimit/2
0
31/35
L6238
Table 6: Phase Delay.
Phase_Dly_2
0 0 0 0 1 1 1 1
Phase_Dly_1
0 0 1 1 0 0 1 1
Phase_Dly_0
0 1 0 1 0 1 0 1
Delay, in Electrical Degrees 0.0 9.4 18.80 20.68 22.56 24.44 (Default) 26.32 28.20
Table 7: Lock Threshold (Fsys = 10MHz)
Lock_1 0 0 1 1 Lock_0 0 1 0 1 Threshold, in s 6.4 12.8 25.6 51.2 (Default)
Table 8: Auto-Start Delay.
Auto_Start_Dly_1
0 0 1 1
Auto_Start_Dly_0
0 1 0 1
Delay, in Seconds 90Hz Input 0.711 1.422 2.133 2.844 60Hz Input 1.07 2.13 3.2 4.27 (Default)
Table 9: Status Register.
Status Bit # 0 1 2 Signal Name Control Function Description These two bits are a wrap-around of their corresponding control bits for test purposes. Logic Follows Control_0 Follows Control_1 When the motor controller detects a zero crossing, Mask will go low and remain low for 15 electrical degrees after the next commutation. Upon detection of a zero crossing, Delay will go high for a time determined by the Phase Delay Control bits. After the delay period, Delay will go low, initiating the next commutation. Signifies whether the rotor is in the alignment phase of start-up or is ramping up to speed Separates the align 1 = Detect Bemf 0 = Mask out Bemf 1 = Delay 0= Commutation 1 = Run 0 = In Start Up 1 Default State 0 0 1/0
Control_0 Control_1 Mask
3
Delay
0/1
4
Go
5 32/35
Align
L6238
Table 9 (continued)
Status Bit # 5 Signal Name Control Function Description Separates the alignment times during startup. While low, the rotor will align to phase 1. When high, the rotor will align to phase 3 until pllaced in the Go mode. Indication of motor Phase relative to Fref. (Must be used in conjunction with Up). Indication of motor Phase relative to Fref. (Must be used in conjunction with Dn). Indicates whether the motor`s frequency is greater or less than the reference frequency. Determines if Phase Difference is within threshold limits as set by control bits. This bit toggles at the zero crossing Detects a fault due to motor failing to spin. If upon entering the Go mode after the double align, no generated Bemf is detected, a 419ms timer, (Fsystem = 10MHz) will cause the outputs to tri-state and flag a fault. This signal cycles once every revolution, providing a source of feedback for the phase detector to lock onto. This signal is not used when EXT/INT or Ext/Int are a logic 1. Indicates an overtemperature fault. Output stage tristates. Early overtemperature warning signal. Indicates a fault due to a rapid deceleration of the rotor caused by a sudden frictional loading. Logic 1 = 2nd Alignment 0 = 1st Alignment 1 = Phase > 0 0 = Phase 0 1 = Phase > 0 0 = Phase 0 1 = Fref > Fmtr 0 = Fref < Fmtr 1 = In Phase 0 = Out of Phase Toggles 1 = Normal 0 = Fault 0 0 1 Default State 1
Align
6 7 8
Dn Up Updn
1 0 1
9 10 11
Lock Spin_ Sense Stkrtr
12
IntFmtr
1 cycle = 1 revolution
0
13 14 15
OTshdown OTw arn Mono
1 = Normal 0 = Overtemp 1 = Normal 0 = Overtemp 1 = Normal 0 = Fault
1 1 1
33/35
L6238
PLCC44 PACKAGE MECHANICAL DATA
DIM. MIN. A B C D d1 d2 E e e3 F F1 G M M1 1.16 1.14 14.99 1.27 12.7 0.46 0.71 0.101 0.046 0.045 17.4 16.51 3.65 4.2 2.59 0.68 16 0.590 0.050 0.500 0.018 0.028 0.004 mm TYP. MAX. 17.65 16.65 3.7 4.57 2.74 MIN. 0.685 0.650 0.144 0.165 0.102 0.027 0.630 inch TYP. MAX. 0.695 0.656 0.146 0.180 0.108
D D1 A D3 A1 48 49 33 32
0.10mm Seating Plane
A2
B
E3
E1
64 1 e 16
17 C
L1
E
L
K
PQFP64
34/35
B
L6238
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. (c) 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore Spain - Sweden - Switzerland - Taiwan - Thaliand - United Kingdom - U.S.A.
35/35

▲Up To Search▲

Price & Availability of L6238

	To Download L6238 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .